Raised-panel steel
Carriage house
Modern flush
Full-view glass
LiftMaster openers
Chamberlain openersFull 25-point door and opener safety check with every visit - springs, cables, rollers, tracks, and your LiftMaster or Chamberlain opener included
You get a price before we start. It does not change when the pro arrives.
Get your free estimateFast, Reliable Garage Door Opener Repair Across Burien
If your opener groans, jerks, or reverses the door halfway down, we can help. We handle garage door opener repair for homeowners across Burien, from the ramblers off Ambaum Boulevard to the split-levels up toward Three Tree Point. Burien’s older garages have their own quirks, and we work on the exact hardware you already have rather than pushing a replacement. Call (866) 937-7308. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Why Burien Homeowners Call Kent Garage Door Repair Co for Garage Door Opener Repair
Burien is a city of self-reliant homeowners, and plenty of them have already tried tightening the rail or swapping the remote before they call. That’s fine. Our technicians have up to 15 years of experience, and we start by figuring out whether the opener is actually the problem. Often it isn’t.
We’re certified to service eight major garage door brands, including LiftMaster, Chamberlain, Genie, Clopay, Amarr, Wayne Dalton, Craftsman, and Raynor. When we arrive in Burien, we already know the hardware. No guessing at a unit we’ve never opened.
Response time to Burien is short. We’re just down the road in Kent, and the drive up Highway 509 or Ambaum is quick. We keep our pricing transparent, quote the job in writing before we start, and offer free estimates. Same-day repair is often possible, and emergency garage door service is available when a broken door leaves your home unsecured or your car trapped. Call (866) 937-7308 for a straight answer.
Styles & brands we work with
- Raised-panel steel
- Carriage house
- Modern flush
- Full-view glass
- LiftMaster openers
- Chamberlain openers
Our Garage Door Opener Repair Services in Burien
Opener Repair
Most openers that strain or reverse aren’t failing motors at all. On Burien’s post-war ramblers, the motor is usually the last thing to go. We check spring balance, the opener rail, photo-eye sensors, and track alignment before we condemn a unit that still has years left. Repair-first, always.

Opener Installation
When a motor really is finished, a new opener installation in Burien typically runs $250 – $550. We match the unit to the door’s actual weight and the opening’s width, which matters on these narrow single-car garages sized for a 1950s sedan. The written estimate sets the final price, and the price is agreed before any work starts.

Smart Opener Upgrade
If you want phone control, scheduling, or alerts when the door opens, a smart opener fits most older Burien garages. We work across LiftMaster, Chamberlain, and Genie systems, and we’ll tell you honestly whether your current unit can be upgraded or needs replacing to get there.

Keypad Entry
A keypad is simple, useful, and takes minutes to program once it’s mounted and wired correctly. On Burien homes where the garage door is the everyday entrance, a keypad means nobody’s left fishing for a remote in the rain.
We also handle remote programming and battery backup for units that lose power during winter storms.
Trusted Brands We Service in Burien
We service LiftMaster, Chamberlain, Genie, Clopay, Amarr, Wayne Dalton, Craftsman, and Raynor. That covers most of what’s hanging over Burien driveways right now, from original 1970s units to recent smart installs. We don’t stock parts on a truck or claim same-visit repairs we can’t make. What we do is diagnose accurately, tell you what’s failing, and schedule the fix fast. If your opener is a Wayne Dalton or a Craftsman from the hardware store, we know it. If it’s a LiftMaster with a battery backup, we know that too.
Common Garage Door Opener Repair Problems We See in Burien Homes
- Openers that strain or reverse halfway down. A fatigued torsion spring, not the motor, is usually failing to carry the door’s weight. The wet marine air off Puget Sound quietly degrades springs and drums, throwing the door out of balance.
- Rusted drums, cables, and end bearing plates. Year-round humidity in the Puget Sound lowlands rusts steel faster than in drier inland cities. That drag jams the opener rail and makes a healthy motor look weak.
- Photo-eye sensors knocked out of alignment. Narrow 1950s garage openings that modern SUVs barely clear clip the sensor beam on the way in. The door reverses, and homeowners assume it’s the opener.
- Rotted wood bottom panels and worn weather seals. Burien’s post-war wood overhead doors absorb moisture every winter. A rotted bottom panel changes the door’s weight and can bind the track, adding load the opener wasn’t sized for.
What Makes Opener Repair in Burien Different
Burien’s 1940s-60s tract ramblers were framed with narrow single-car garage openings sized for a 1950s sedan. A modern SUV barely clears the weather seal and often clips the photo-eye sensor beam on the way in. That fit problem doesn’t exist in the newer infill townhomes near the transit corridor, which mostly use insulated sectional steel doors and wider openings. It’s a genuinely Burien-specific issue, and it explains a lot of the sensor and alignment calls we get.
Here’s how a typical job usually goes on one of these ramblers. A homeowner presses the remote and the opener strains, jerks, or reverses the sectional door halfway down. The opener motor gets blamed. But the real culprit is usually a fatigued torsion spring or rusted drums and cables that the damp marine air has been quietly degrading, throwing off door balance. A qualified local pro checks spring cycles and door balance first, then the opener rail, photo-eye sensors, and track alignment, replacing the spring and cables before condemning the LiftMaster or Chamberlain unit. An opener straining under a 150- to 350-pound door is describing a spring symptom, not a motor failure. Because so many of these garages were an afterthought, we also correct the narrow opening, weather seal, and end bearing plates in the same visit so it’s done right in one trip.
See the difference
Before
After
Before
After
Before
AfterPricing for Garage Door Opener Repair in Burien, WA
A typical garage door opener repair in Burien runs $120 – $320. What affects the number is what’s actually failing: a sensor realignment sits at the low end, a gear, capacitor, or logic board job climbs toward the top. If the spring is the real culprit, spring repair runs $180 – $340 for one spring, and a matched pair is usually replaced together, so a pair costs about twice that. Cable repair runs $130 – $250, and track realignment $120 – $240. We quote in writing before any work starts, so the price you agree to is the price. Estimates are free. Call (866) 937-7308.
| Service | Typical Estimated Range |
|---|---|
| Opener Repair | $120 – $320 |
| Opener Installation | $250 – $550 |
| Spring Repair (one spring) | $180 – $340 |
| Cable Repair | $130 – $250 |
| Track Realignment | $120 – $240 |
We Also Serve Cities Near Burien
We also take calls in SeaTac, Tukwila, Des Moines, and Bryn Mawr-Skyway. The housing stock shifts a little as you head south, but the opener problems are familiar ones. If you’re just outside Burien and wondering whether we’ll come out, the answer is usually yes.
Serving Burien, WA – Our Local Coverage Area
We serve Burien and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
FAQs – Garage Door Opener Repair in Burien
It’s almost always the spring, not the opener. A fatigued torsion spring stops carrying the door’s weight, so the opener works harder than it was built to. We check spring cycles and door balance first, then test the opener itself. If the spring is the problem, replacing it fixes the strain. Call (866) 937-7308 for an exact quote – estimates are free.
Year-round humidity and heavy winter rain rust steel drums, cables, and end bearing plates faster here than in drier communities east of the mountains. That added drag makes openers strain and jam. Wood doors rot too, and a rotted bottom panel changes the door’s weight. The opener gets blamed for a moisture problem behind it. Call (866) 937-7308 and we’ll sort out which is failing.
Ask the technician what cycle rating the replacement spring carries before it goes in. Cycle figures vary by spring and door weight, so a qualified pro will match the spring to your door rather than quote a standard number. Heavy doors on older Burien garages need the right spring, not just any spring. Call (866) 937-7308 for a written estimate.
Yes, in most cases. Narrow openings don’t stop a smart opener from working, as long as the unit matches the door’s weight and the rail fits the space. We work across LiftMaster, Chamberlain, and Genie systems and will tell you if your existing unit can be upgraded or needs replacing. Call (866) 937-7308 for a free estimate.
We diagnose on the first visit and schedule the parts you need based on what’s actually failing. Battery backup and remotes for those brands are readily available and scheduled quickly, but we don’t claim same-visit stock we can’t guarantee. The written estimate sets the final price before any work starts. Call (866) 937-7308.
Get Your Burien Opener Fixed
Whether your opener is straining against a tired spring or your sensor keeps tripping on that narrow rambler opening, we can diagnose it and give you a straight answer on repair versus replacement. Call (866) 937-7308 for a free estimate. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Written by the team at Kent Garage Door Repair Co.